Frequently Asked Questions:

1. What is Formula 62?
2. How does it work?
3. Is Resonant Vibrations Effective?
4. Are there any limitations?
5. What can I use it on?
6. How do you know it's done?
7. How can I tell when stresses have been reduced?
8. Is it difficult to set up and use?
9. What size parts can I use it on?
10. Can it replace thermal?

What is "Formula 62"? Back to Top
"Formula 62" is a resonance based method of vibratory stress relief developed by Stress Relief Engineering Co. Work pieces are subjected to low frequency, high amplitude vibrations for a short period of time based on the weight of the work piece. This allows the residual stress to be reduced to a much lower level where static equilibrium is restored. The resonance method used by researchers around the world in stress relief studies using vibration and is currently considered an industry standard.

How Does It Work? Back to Top
Low frequency vibrations are used as a carrier to deliver high amplitude energy to a metal fabrication, or machined part. The heavy vibrations Produce a load that is superimposed on the existing stress patterns that result in a reduction of peak residual stresses. This produces a more Dimensionally stable product and reduces the random distortion that often occurs in unstable work pieces.

Are Resonant Vibrations Effective? Back to Top
Resonant vibrations have been found to be the most effective means for reducing residual stresses by vibration. The resonant frequency vibration method has a much more pronounced stress redistribution compared to the sub resonant frequency methods. High amplitude resonant vibrations are very efficient in significantly reducing peak residual stresses in weldments.

Are There Any Limitations? Back to Top
There are some limitations as with any metalworking process. The process is not recommended for extrusions or severely cold worked items. On very large, very long or open space frame type structures, the vibration may need to be applied at several locations which does require more time. Very small items in large quantities are more easily treated thermally in batches. In welding situations where vibration is used during the welding process, this method is most compatible with SMAW, GMA and GTAW welding processes. Other welding practices may present formidable logistical problems.

What Can I Use It On? Back to Top
The process can be used on a wide range of ferrous and non-ferrous metals. Typical materials are: carbon steels, stainless steel, aluminum, cast iron, manganese, incolnel, etc. These are a few of the metals that can be treated in a variety of conditions such as: wrought or cast, forged, formed, welded, ground, polished or machined.

How Do You Know When It's Done? Back to Top
As with any treatment process, one must follow a given recipe to achieve success. In a thermal process, treatments are governed by a practice that dictates so many degrees per hour per inch of thickness. In the vibratory or non-thermal mode, the treatment is predicated on a time vs. weight basis where the aggregate weight of the part, including any associated tooling or fixturing attached to the part, is used to determine the length of time for treatment after resonance has been determined.

How Can I Tell When Stresses Have Been Reduced? Back to Top
The most direct way, and the most rewarding, is to resolve a basic dimensional instability problem. This is quite apparent when standard measurement techniques confirm that the part is now holding dimensions that previously moved in random fashion. However, in most stress relief applications, there is no major dimensional problem to overcome and the part looks the same before and after treatment. What now? Is there any simple way to tell how well we've done? Unfortunately, no! There have been some very technically weak and scientifically unsupported methods promoted over the years that allegedly indicate when stress relief occurs. Some of these methods claim that motor current changes are a means to indicate when the part is relieved or that vibration frequencies change as the stiffness of the part changes due to less resistance from stress or the part undergoes a vibration frequency change from an unnatural mode to a natural mode. While we all would like to see some evidence of change, it just isn't that simple. Real quantitative proof of stress relief efficiency can be obtained for virtually any metal using the right analytical tools. Whether you are using heat, vibration or a cryogenic technique for stress relief, you should only rely on known and approved analytical methods for determining when stresses have been reduced. This is very important because, not only do we need to know the magnitude of the stress concentration, but we also need to know whether it is tensile or compressive. There is no simple toot or technique available that can supply all of these data requirements for a three dimensional object. Measurement techniques used by researchers are well known and we strongly support them. We highly recommend x-ray diffraction per ASTM Eg 1 5-83, high speed hole drilling with strain gauges per ASTM E837-85 or for ferromagnetic materials, the Barkhausen Noise Analysis method, for making any kind of determination that stresses have been reduced.

Is It Difficult To Set Up And Use? Back to Top
Not at all! There are a few rules that must be followed and they apply to all applications. The first requirement is to isolate the work piece, as much as is practically possible, so it is free to vibrate. In cases where this is not possible, the vibration unit must be located as close as possible to the work area. The unit must be directly coupled to the work piece in order to transfer the vibration energy into the work piece. This can be accomplished by using clamps, fasteners or adaptive fixtures. Once these conditions are met, the part must be vibrated for a minimum period of time based on weight. Parts can be vibrated for longer periods without suffering any fatigue damage or loss of tensile strength. The equipment is designed for ease of operation and is used both in shop environments and field applications by your personnel.

What Size Parts Can I Use It On? Back to Top
The "Formula 62 " equipment can be used on a wide variety of shapes and sizes from small castings, shafts, gears, or OEM products to very large welded and machined fabrications that are too large for thermal treatment. Using a special vibration table designed specifically to hold smaller parts, the vibration system can be set up right in the production area which saves time and makes it possible to treat numerous parts at one time. The table has a capacity of 2000 lbs. or 910 Kg., which makes it ideal for molds, die sets or other heavy work pieces.

Can it Replace Thermal? Back to Top
In cases where the thermal method is used solely to promote dimensional stability of the part for alignment purposes, surface integrity or service conditions, the vibration method can be used as a much more cost effective replacement. This method also allows the machinist or fabricator to treat parts at various points throughout the manufacturing process that otherwise would be too costly or impossible to do, due to surface considerations. The thermal stress relief process, while adequate for many metals, does have some serious limitations that make vibratory stress relief a far better choice. For example: AWS DI. I do not recommend thermal treatment of A514, A517, A709 or Grade 100 material. Other carbon or low alloy steels may undergo undesirable changes in microstructure, causing a deterioration of mechanical properties, cracking, or both. Additional consideration must be given to possible distortion, oxidation, loss of corrosion resistance or intergranular cracking that may result from the heat treatment. While the method is good, it's not perfect.

 
CNC Machine Sales | 1332 West Collins Ave. | Orange, CA 92867 | (714) 335-5447
HOME | PRODUCTS | INQUIRY FORM | TESTIMONIALS | FAQ'S | ABOUT US | LINKS